Commercial cleaning robot maintenance checklist: daily, weekly, monthly and what wears out first
Short answer: On a commercial cleaning robot, four parts do most of the wearing out: brushes and pads, squeegee blades, filters and the battery. Site staff can look after all four with a few minutes a day: rinse and inspect the squeegee and brushes after every run, clean or tap out the filters, and charge the battery the way the manual says. A technician then replaces the worn parts on a monthly or quarterly visit. The manuals we read agree on the pattern but not on the numbers: one quick start guide lists a 150-hour life for scrub pads and 300 hours for disc brushes and squeegee blades, another lists 30 days for a side brush and a HEPA filter, and one maker suggests replacing squeegee rubber every one to three months depending on how hard the site is. Use your model's manual for the intervals; use this page for what to look at and when to replace.
This page is for facility managers, cleaning contractors and robot makers running robotic floor scrubbers and vacuums in Canada and the US. It goes part by part. The whole-robot schedule (sensors, firmware, maps, docks, delivery robots and who does what) is in our robot preventive maintenance schedule. Manufacturer wording below is quoted from public manuals and quick start guides, checked on 2026-11-12; brand names are used only to cite those documents.
Before any maintenance: power off
Every manual we read starts here. A rider-scrubber manual says: "Before leaving or servicing machine, stop on level surface, turn off machine, and remove key." A compact scrubber robot's guide says: "Do not perform cleaning or maintenance work while the machine is powered on and running." Two more rules show up repeatedly and are easy to break on a busy night shift:
- No hose or pressure washer on the machine. "Do not power spray or hose off machine. Electrical malfunction may occur. Use damp cloth."
- No steam on the tanks. "DO NOT use steam to clean tanks. Excessive heat can damage tanks and components."
What wears out first
Two quick start guides for autonomous scrubbers and sweepers, published by a US distributor, list expected part lives. They are the clearest public numbers we found; one notes that lifespans vary by location, and that applies to both:
| Part | Published life (hours of use) | Published life (days, at about 3 h a day, 5 days a week) | Replace when |
|---|---|---|---|
| Scrub pads | 150 h | n/a | No longer clean effectively; both sides used |
| Filter bag / filter cartridges | 100 h / 150 h | Dust bag 45 days; HEPA filter 30 days | Darkened, discoloured or torn |
| Side brush | n/a | 30 days | Bristles frayed or missing |
| Disc brushes / roller brushes | 300 h | Roller brushes 90 days | Bristles worn down to the coloured indicator bristles |
| Squeegee blades | 300 h | 90 days | Thin, torn or darkened; all edges used |
| Steel wire filters / cylindrical filter | 1,000 h | 180 days | Damaged |
So the order is roughly: pads and dust filters first, then brushes and squeegee blades, then the coarse filters, with the battery on a much longer clock. Floors change the order. Grit, grout lines and rough concrete chew through blades and pads; chemicals matter too. On a site that tracks lobby grit all winter, squeegee blades can easily become the first item. One maker's guide for a compact scrubber robot recommends replacing the front and rear squeegee rubber "every 1 month" in high-wear environments, every 2 months in medium and every 3 months in low.
1. Brushes and pads
Daily (site staff). Lift or remove the brushes and pull off hair, string and wire. A rider-scrubber manual asks operators to "check scrub brushes daily for wire or string tangled around the brush or brush drive hub". A compact robot's guide explains why it matters: if brushes aren't cleaned for long periods it "will affect cleaning performance and may even shorten the motor's lifespan". Wrapped string is a brush motor fault waiting to happen.
After each use: pads. Wash pads with soap and water and let them dry. One manual says: "Do not wash the pads with a pressure washer. Hang pads, or lie pads flat to dry." Another notes that "both sides of pads can be used to maximize cleaning quality and lifespan", so flip before you replace.
Replace when. Most brushes have coloured indicator bristles: replace when the normal bristles have worn down to the indicator's height, or, in one manual's words, "when they no longer clean effectively". Replace in sets: "Always replace brushes and pads in sets. Otherwise one brush or pad will clean more aggressively than the other."
Signs to report. Swirl marks or a stripe of dirty floor on one side, a brush that won't lower, a burning smell or a brush motor fault code. These are often hair or string in the hub, not a failed motor. Check before booking a repair.
2. Squeegee blades
The squeegee is what leaves the floor dry. A worn or nicked blade leaves streaks and puddles, and that is usually the first complaint a building manager makes about a cleaning robot.
After every run (site staff). Wipe both blades, clear grit and hair from the blade edge and the squeegee hose inlet, and check that the blades sit flat. One quick start guide: "Using a cloth or sponge, wash the squeegee blades to remove all grime and debris."
Daily check: wear and damage. A rider-scrubber manual puts it most clearly: "Check the squeegee blades for damage and wear daily. When the blades become worn, rotate the blades end-for-end or top-to-bottom to a new wiping edge. Replace blades when all edges are worn." Many blades have four usable edges, so rotating can multiply blade life before you buy new ones.
Replace when. All edges are rounded or nicked, the rubber is torn, hardened or darkened, or water is left behind after you've ruled out a clogged hose or a full recovery tank. Rider-scrubber and compact-robot troubleshooting tables both list worn squeegee blades as a cause of poor water pickup. Replace front and rear blades together, and keep a set on site; see how many spares to stock.
Chemicals. A detergent the maker hasn't approved can swell or crack squeegee rubber and seals. When the site changes chemical supplier, check the new product against the robot's compatibility list.
3. Filters
Filters protect the vacuum motor. A clogged filter means weak suction, water left on the floor and a motor that runs hot. Filter type depends on the robot, and so does the care:
- Vacuum fan or recovery-tank screen filter (scrubbers): daily. Usually rinsed and left to dry. One rider-scrubber chart lists "Vacuum fan filter — Clean" as a daily operator task. Don't reinstall a wet filter.
- Dust filters on sweepers and vacuums: tap, don't wash, unless the manual says so. One guide for a compact robot's filter sponge says "Washing is not recommended" (tap it clean and replace it if heavily soiled). A vacuum robot's manual says: "Do not wash the HEPA filters with water."
- Solution (clean water) filter: by hours. One rider-scrubber manual says to remove and inspect the solution tank in-line filter "after every 50 hours of operation". A clogged solution filter looks like the robot isn't putting down water.
- Recovery tank: daily, at the end of every run. Drain, rinse and leave open to dry. One maker warns that dirt left in the dirty-water tank "will produce foul odors and can easily lead to clogging of the drainage valve". Empty it where the building tells you to, never into a storm drain.
Replace when. Torn, holed, deformed or darkened filters, or suction still weak after cleaning. Dust filters on vacuums and sweepers are usually the shortest-lived part on the robot (see the table above), so they're the item most worth keeping in stock.
4. Batteries
Cleaning robots use either lead-acid (flooded or sealed AGM) or lithium-ion packs, and the care is different. Check which one you have before following any battery advice, including this page.
Flooded lead-acid
- Weekly: check the water level. One rider-scrubber manual: "Check the battery electrolyte level weekly." Add distilled water only, and only after a full charge. A battery maker's guide says: "Fully charge the batteries prior to adding water", topping up to 1/8" (3 mm) below the vent well. Overfilling makes the electrolyte overflow when it expands during charging.
- Charge once a day, after real use. The same manual says: "Do not charge the batteries more than once a day and only after running the machine for a minimum of 15 minutes." Topping up a flooded pack after a few minutes' run shortens its life.
- Don't run it flat. The battery maker says: "Do not discharge your battery more than 80%." Equalising is for flooded batteries only, never AGM or gel.
- Every 200 hours: terminals. The manual says to check for loose connections and clean the battery tops, terminals and cable clamps with a baking soda and water solution.
- Safety. Charging lead-acid batteries gives off hydrogen. Charge in a ventilated spot, keep covers open while charging and keep metal tools off the battery tops.
Lithium-ion
- No watering, and partial charges are fine. One maker's announcement of lithium packs for its robotic scrubbers says the pack "does not require watering" and that lithium-ion batteries "allow opportunity charging": the robot can be plugged in any time, even if the battery isn't fully discharged.
- Don't let it sit empty. A compact robot's guide says to keep the battery level "above 10% at all times" and warns that a robot left unused for more than 30 days may be completely depleted. A deeply discharged lithium pack may refuse to charge again. Robots in storage need a charge before storage and a top-up every few months, at the interval your manual gives.
- Original charger and dock only. The same guide says: "It is strictly forbidden to use non-original chargers to charge the robot."
- Spare and damaged packs. Lithium-ion batteries ship as dangerous goods, and a swollen or damaged pack needs special handling. Order spares before you need them; see the battery section of our maintenance schedule.
Signs to report (either type). Run time noticeably shorter than last month, the robot returning to the dock early, charging errors, a hot or swollen pack, or corrosion on the terminals. Short run time can also be a dirty charging contact or a charger fault, so record the battery health figure from the service tool before you replace a pack.
The checklist
Print this and tape it next to the dock. Intervals marked "typical" are planning defaults; where your manual gives a number, use the manual's.
| When | Brushes and pads | Squeegee blades | Filters and tanks | Battery | Who |
|---|---|---|---|---|---|
| After every run | Remove hair and string; wash pads, dry them | Wipe both blades; clear the hose inlet | Drain and rinse the recovery tank, leave open; empty the debris tray or dust bin | Robot back on its dock and charging | Site staff |
| Daily | Check wear and indicator bristles | Check edges for wear and nicks; rotate a worn edge | Clean the vacuum or tank screen filter (as the manual says: rinse or tap) | Check charge status; lithium: don't leave below the manual's minimum | Site staff |
| Weekly | Flip pads | Check blades sit flat and wipe the full width | Rinse the suction hose; tap out or check dust filters | Flooded lead-acid: check water level after a full charge | Site staff |
| Monthly (typical) | Replace pads or brushes at the wear line, in sets | Replace when all edges are used (high-wear sites) | Clean the solution filter; replace darkened or torn filters; check tank seals | Clean charging contacts on robot and dock | Trained staff or technician |
| Quarterly (typical) | Check the brush drive and brush motor | Replace blades (medium and low-wear sites) | Check the vacuum motor and hoses | Read battery health in the service tool; lead-acid: clean and tighten terminals | Technician |
Keep a parts log. Note the date and robot for every brush, pad, blade, filter and battery replacement. After two or three months the log tells you your site's real intervals, which robot is working hardest, and what to order before it runs out. It also makes warranty conversations with the maker much easier.
What a maintenance visit costs
Daily and weekly care should cost you nothing but staff minutes. For the monthly or quarterly visit, example only at KeepRobots' current published rates (CAD, before tax and parts): a Greater Vancouver site with two cleaning robots, assuming about 1.5 hours on site to replace blades, brushes and filters and read battery health. That comes to the $100 call-out plus 1.5 × $150 labour, $325 per visit, plus parts at parts price. The hours are an assumption; real time depends on the model and its condition. If the visit finds a fault that needs a repair, that is quoted separately before any work. For US sites, labour is US$150 per hour and travel is quoted per project; outside the Greater Vancouver core area, travel is quoted per project. A larger worked example (four robots, quarterly) is in our maintenance schedule.
What KeepRobots can do
KeepRobots is a robot field service company based in Greater Vancouver, serving Canada and the United States in English and Mandarin. We don't make robots and are not an exclusive agent for any brand; in Canada we also sell robots from selected brands (Booster Robotics and SENAD), and we maintain cleaning robots of any make. For sites running cleaning robots, we can do scheduled maintenance visits to the maker's manual, replace wear parts, read battery health and fault logs, and train night staff on the daily checklist. For robot makers, we can hold consumables such as brushes, blades and filters in Vancouver and be your local maintenance team, working from your Chinese or English documentation. See cleaning robot field service, cleaning robot service in Vancouver and robot repair and maintenance. Email support@keeprobots.com (sites) or partners@keeprobots.com (robot makers) with the model and how many robots you run.
FAQ
What wears out first on a commercial cleaning robot?
Usually scrub pads and dust filters, then brushes and squeegee blades. Two published quick start guides list pads at 150 hours, filter bags at 100 hours, disc brushes and squeegee blades at 300 hours, and HEPA filters and side brushes at about 30 days, and lives vary by site. On gritty floors, squeegee blades often go first.
How often should squeegee blades be replaced on a robotic scrubber?
When all wiping edges are worn, not on a fixed date. Check them daily and rotate to a new edge when one wears. Published guidance ranges from about 300 hours of use to every one to three months depending on how hard the site is on them. Replace front and rear blades together.
Can I wash cleaning robot filters with water?
It depends on the filter. Scrubber screen and vacuum fan filters are often rinsed and dried; HEPA and sponge dust filters often must not be washed. One vacuum robot's manual says "Do not wash the HEPA filters with water". Follow your model's manual and never reinstall a wet filter.
How do I look after a lead-acid battery in a robotic floor scrubber?
Check the water level weekly and add distilled water only after a full charge. Charge once a day after real use rather than topping up after short runs, don't run the battery flat, and clean the terminals periodically. Lithium-ion packs need no watering and can be charged any time, but shouldn't be left empty.
Can site staff do cleaning robot maintenance themselves?
Yes for the daily and weekly items: rinsing tanks, cleaning brushes, blades and filters, and checking water levels and charging. Replacing wear parts can also be done by trained staff on many models. Motor, wiring, battery replacement and anything that needs the maker's service tool should go to a technician; under warranty, check with the maker first.
How much does a cleaning robot maintenance visit cost with KeepRobots?
Before tax and parts: a CAD $100 call-out in the Greater Vancouver core area plus CAD $150 per hour on site. For example, two robots at about 1.5 hours is $325. US labour is US$150 per hour; travel outside the core area and in the US is quoted per project. Repairs found during a visit are quoted before any work.
Sources (checked 2026-11-12)
- Tennant, T7AMR Rider-Scrubber Operator Manual 9018134 (squeegee, brushes and pads, filters, flooded batteries, safety): tennant (PDF)
- Tennant, T380AMR Rider-Scrubber Operator Manual 9020999 (solution in-line filter, maintenance chart): tennant (PDF)
- Tennant, news release on lithium-ion batteries for AMR floor cleaning machines, 2022-04-05: tennantco.com (PDF)
- Pudu, CC1 Operation Guide V6.0 (squeegee rubber replacement, brushes, filter sponge, dirty-water tank, battery level, charger): academy.pudutech.com
- SoftBank Robotics, Whiz Operational Manual v1.8 (HEPA filters): ushelp.softbankrobotics.com (PDF)
- SoftBank Robotics America, Phantas Quick Start Guide P80100052A02 (consumable lifespans in days): ushelp.softbankrobotics.com (PDF)
- SoftBank Robotics America, Scrubber 50 Pro Quick Start Guide P30100054A02 (consumable lifespans in hours, after-use tasks): ushelp.softbankrobotics.com (PDF)
- Trojan Battery, Flooded Battery Quick Start User's Guide (watering, depth of discharge, equalising): Trojan document (PDF, reseller-hosted)
- KeepRobots current rates: robot repair and maintenance
Brand names are used only to cite their public documents; intervals quoted belong to the model named in each document and are not industry rules. KeepRobots is an independent field service company and is not affiliated with or authorized by these manufacturers. Example costs use KeepRobots' current published rates as of 2026-11-12, before tax and parts, and may change; hours in examples are assumptions. Your robot's manual takes priority over this page.